Surebonder 9610A Installationsanleitung PDF herunterladen (Seite 3)

Preparing for Use

If the stapler has been stored in a cold environment, bring it to a warm area and allow it to warm

up before using.

- Make sure stapler is disconnected from air supply.

- Only use the proper size and type of staple with this stapler, as specified under "Staples".

- Depress the track release lever to release the spring-loaded staple magazine; slide the magazine

out (back) as far as it will go.

- Turn the stapler upside down. Place a full strip of staples into the staple magazine, with the

staple points facing upward (away from the tool). Slide the staple magazine closed until the

track release lever snaps back into place with a click. (Closing the staple magazine while

staples are loaded engages the spring-load mechanism, so it will take slightly more pressure to

slide the magazine closed.)

Using the Stapler

- This stapler is equipped with a contact safety mechanism; the trigger will not operate unless the

contact mechanism is firmly depressed against the surface to be stapled.

- Grip the body of the stapler firmly, make sure that the contact mechanism is placed securely

against work surface, and pull the trigger to drive a staple.

- Remove finger from the trigger.

- To drive another staple, move the stapler to next area on work surface to be stapled, and repeat

these steps.

After Stapling

- Disconnect the air hose from the stapler.

- Remove all staples from the staple magazine of the stapler.

- Place several drops of oil (included in case) into the air plug.

- Shut off air compressor and drain any moisture from the compressor tank.

- Drain the air line filter; clean the filter element, then blow air in opposite direction to remove any

dirt/debris.

- Keep lubricator filled with oil (included in case).

Clearing Staple Jams

- Disconnect the air hose from the stapler.

- Carefully remove staple strip from staple magazine.

- Remove any remaining loose staples from inside the staple magazine, using pliers to grasp the

staples, if necessary.

- Once jammed staples have been removed, reload stapler.

100

120

140

160

Lubricator Regulator Filter

To compressor

To Air Tool

Quick Connector Quick Coupler

APPLICATIONS

Including, but not limited to: insulation, roofing felt, house wrap, auto and marine vinyl trim,

cabinet felt, cabinet backs, screen door repair, small furniture, light trim, molding and picture

frames, and general staple use.

FEATURES

- View window for staples

- Adjustable exhaust

- Rubber hand grip for comfort

- Firing Safety mechanism

- Easy drop-in staple loading

OPERATION

The Surebonder 9610 Pneumatic Stapler is designed to use No.6 heavy-duty wide crown

staples in 1/4”, 5/16”, 3/8", 1/2", and 9/16” leg lengths. For best results, use Surebonder Heavy

Duty Staples.

AIR SUPPLY

This stapler is designed to operate on clean, dry, regulated compressed air, between 60 and

100 psi. It is preferable to include an air filter, pressure regulator, and automatic oiler within 15

feet of the tool, if possible.

An air filter is needed to remove contaminates and moisture that are contained in compressed

air; filtering will significantly prolong the life of the tool. If an automatic oiler is not installed,

place 5 to 6 drops of oil into the tool's air inlet at the beginning of each work day.

The staple gun comes factory-equipped with a male quick connector. The staple gun must

always be connected to the air supply with a coupling that removes all pressure when it is

disconnected.

NOTE: all components used with this staple gun (air hose, connectors, regulators,

filters, etc) must be rated at 120 psi, OR 120% of the maximum compressor

potential, whichever is higher. Do not connect this staple gun to a system with

maximum potential air pressure greater than 200 psi.

AIR CONNECTION SETUP

1 2 3 4

Kommentare zu diesen Handbüchern

Keine Kommentare

Surebonder 9610A Installationsanleitung Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nagelpistole Surebonder 9610A