IMPORTANT SAFETY WARNINGS:
THE SAFETY WARNINGS BELOW CANNOT COVER ALL POSSIBLE SITUATIONS THAT MAY
OCCUR. THESE BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO PROTECT
AGAINST PERSONAL INJURY TO THE OPERATOR OR OTHER PERSONNEL IN THE AREA, AS
WELL AS DAMAGE TO THE EQUIPMENT. READ AND UNDERSTAND THESE WARNINGS BEFORE
USING EQUIPMENT.
Keep tool away from children, and DO NOT allow children near work area. Do not allow children
or untrained personnel to handle this tool.
DO NOT operate this stapler while tired, or under the influence of drugs, alcohol, or medication
that makes you drowsy.
Never point the stapler at yourself or others - always assume that the stapler is loaded, and
proceed with caution.
Wear safety glasses and ear protection. The tool operator and all personnel in the work area
must wear safety glasses that protect the front and side, to avoid eye injury. Ear plugs should
be worn to avoid hearing damage.
If operator will be working in a situation where overhead work will be done (i.e. on a ladder,
stairs, or scaffolding) a hard hat must be worn.
Never wear loose clothing or jewelry because it can get caught in the moving parts of this tool.
Make sure long hair is covered, to avoid getting it caught in stapler.
Keep the tool pointed away from yourself and others at all times. Keep hands and all body parts
away from rear area of stapler (near air hose) to guard against injury. Keep hands and feet away
from firing head during use.
Keep proper balance and footing at all times - do not over-reach.
Never use oxygen, bottled gas or any type of combustible fuel as a power source - it can cause
an explosion and serious injury.
Do not use near flammable liquids or gases - the stapler sparks during operation, and could
cause an explosion and serious injury.
Use an air hose that will withstand at least 150 psi, OR 150% of the maximum pressure of the
compressor.
Never connect this tool to compressed air if the pressure could exceed 200 psi, as the stapler
could burst. Use only clean, dry, regulated compressed air, with pressure not exceeding 120 psi.
Disconnect stapler from air supply before loading staples, to prevent a staple being fired during
connection to air hose.
Do not use a non-relieving coupler with this stapler - if used, the stapler could remain charged
with air after disconnecting, and would still be able to drive a staple even after being
disconnected. The stapler and air hose must have a coupling so that all pressure is removed
from the stapler when the coupling is disconnected.
Do not depress the trigger or safety mechanism while loading staples - accidental firing of a
staple can occur. Keep your fingers away from the trigger when not firing staples. Always keep
the stapler pointed downward during loading.
Do not use an air hose that is too long - tool operator can trip over it. Make sure all connections
are tight.
Disconnect air hose from stapler
- before performing maintenance
- when clearing a jam
- when tool is not in use
- when moving it to another location
- when handing stapler to another person
(WARNINGS continued next page)
Seal Kit #9610 - 400 includes:
Seal Kit #9610 - 400includes:
Diagram # Description
Diagram # Description
5 Packing
6 Seal
8 0-Ring(18x2.4mm) (2)
10 0-Ring(31x2.4mm)
11 0-Ring(27.3x3mm) (2)
13 0-Ring(23x2.4mm)
14 0-Ring(40x1.9mm)
17 0-Ring(33x3.5mm)
19 Joint Guide
12 Drive Pin
2 Hex Head Bolt
l7 Spring
20 Seal
21 Switch
22 Spring
23 Step Pin
32 Hex Head Bolt
38 Click Lever Pin
40 Spring
42 Step Pin
45 Spring
Diagram # Description
Hardware Kit #9610 - 420 includes:
Drive Pin Kit #9610 - 410 includes:
Kits available:
www.surebonder.com
Replacement parts below are not available
(6 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern